Surge relief
Protect your pipeline from water hammer and overpressure.

Protect the pipeline from water hammer.
- Protects against water hammer and overpressure
- Relief valves and controls on one skid
- Built and tested in our workshops
- Designed to ASTM, ASME, ISO and API standards
A selection of surge relief skids we have built
Real projects, photographed in our workshops and at site. Ask us for references in your application.




- Diluent injection and surge relief skids, José terminalAmeriven / Vepica
How it works, configurations and standards
Open the sections you need. Everything stays on the page for reference and print.
01How it works
Process diagram and step-by-step timeline
When a pump trips or a valve closes fast, a pressure surge travels through the line. A surge relief skid releases that pressure before it damages the pipeline.
We build the skid in our workshops, with relief valves and controls sized for your line.
Water hammer, also known as the Joukowsky (Zhukovsky) pulse, is a transient caused by changes in fluid velocity and is the main cause of damage to hydraulic systems. Uncontrolled, it can break the pipe by overpressure or by depression and cause serious operating problems. Our skids protect pipes, pumps, vessels and valves, and are designed to your process conditions.
In the order the fluid passes through it. Select a step, use the arrows, or let it play.
Typical schematic configuration, shown for reference only. The final design, equipment, instrumentation and applicable codes depend on the client's process conditions, specification and project requirements, and are defined during engineering.
Swipe sideways to see the whole diagram.
Surge source
A pump trip or a fast valve closure stops the flow suddenly and sends a pressure wave through the line: water hammer.
Tie-in and isolation
The skid connects to the line through an isolation valve, so the equipment can be isolated for maintenance.
Pressure sensing
Pressure transmitters and gauges monitor line pressure and report to the control panel. Relief set points are based on the line limits.
Relief valves
When pressure rises above the set point, the valves open fast and release the surge volume. They reseat when pressure falls.
Discharge header
The released liquid is collected in a discharge header sized for the relieving flow and the allowed back pressure.
Surge tank
The surge volume is diverted to a tank, with level monitoring and vent, or to the destination defined for the project.
Pump-out and return
Once the event is over, a pump returns the liquid to the line or sends it to slops, and the tank is ready again.
Line restored
Valves reseat, pressure returns to normal and the line keeps running without damage to pipe, pumps or valves.
Control panel and SCADA
The panel shows pressure, level and valve position, raises alarms and sends data to your SCADA.
02Typical configurations and options
What goes on the skid and what can change
- Relief valve typeSpring-loaded, pilot-operated or control valve, per the surge study
- Number of valvesOne or several in parallel; spare valve or duty / standby
- Sizing and set pointsFrom your line data, MAOP and surge study
- Pressure sensingPressure transmitters and local gauges
- DischargeHeader to a tank, a return line or slops, as the project defines
- Surge tankOptional tank with level monitoring and vent
- Pump-outPump to return the liquid to the line or to slops
- IsolationBlock valves for maintenance of the relief valves
- ControlsPanel with alarms and valve position monitoring; signals to your SCADA
- MaterialsCarbon steel or stainless steel; NACE materials for sour service
- Area classificationInstruments, panels and wiring selected for the classified area
- MountingSkid-mounted, ready to lift and transport
- Valve and instrument brandsWe integrate Farris, Flowserve, Samson, Mokveld, Westlock, Yokogawa and Swagelok, and consider your preference
03Standards and documentation
Design references and the documents we deliver
Designed to ASTM, ASME, ISO and API standards. The applicable codes are agreed per project.
Typical references
- API 520Sizing, selection and installation of relief devices
- API 521Pressure-relieving and depressuring systems
- API 526Flanged steel pressure-relief valves
- API 2000Venting atmospheric and low-pressure storage tanks
- ASME B31.4Pipeline transportation systems for liquids
- ASME B31.3Process piping
- ASME VIII-1Pressure vessels, including the surge tank if pressurized
Typical documentation package
- P&ID
- General arrangement
- Relief valve datasheets and sizing calculations
- Instrument datasheets
- FAT procedure and report
- Operation and maintenance manual
Factory acceptance test (FAT) in our workshops and site acceptance test (SAT) at the installation site.
Typical brands on this skid
Brands we represent, integrated alongside your preference.




One team, from engineering to the factory test
- Step 1
Engineering
Process, mechanical and instrumentation design from your specification.
- Step 2
Fabrication
Built and assembled in our workshops to the agreed codes.
- Step 3
Factory test (FAT)
Loop-by-loop checks, valve stroking and control verification, with your witnesses if you wish.
- Step 4
Start-up
Documentation, delivery and remote support.
