Controval
Product group

Flow and level measurement

Flow and level instruments for process control, quality and custody transfer. We help you pick the technology that suits your fluid, your line or vessel, and the accuracy you need.

At a glance

We select, supply and integrate flow and level instruments, and support them after delivery.

  • Selection by fluid, line or vessel size, pressure, temperature and accuracy
  • Supply as stand-alone instruments or spares for your installed base
  • Integration into our skids, such as LACT units and test separators
  • Installation, commissioning and spares support
01

Flow measurement

Flow meters tell you how much fluid moves through a line, either as volume or as mass. They are used for process control, allocation, fuel and utility accounting, and transfer between parties. No single technology fits every fluid, so selection comes first.

Request a quote
Yokogawa ROTAMASS Coriolis flow meter

Differential pressure

An orifice plate, venturi or averaging pitot tube creates a pressure drop that a transmitter turns into flow. It is well proven, works with liquids, gas and steam, and has no moving parts. Rangeability is limited, and the primary element needs straight pipe and periodic inspection.

Rotameter

A float rises in a tapered tube until the upward flow balances its weight, and its position shows the flow. It is simple and low cost for local indication of clean fluids. It is mounted vertically and is not suited to dirty or opaque service without special versions.

Turbine

Fluid spins a rotor and the speed is proportional to flow. Turbine meters are accurate and repeatable on clean, low-viscosity liquids and gas. Bearings wear, and viscous or dirty fluids hurt accuracy, so filtration and regular calibration matter.

Positive displacement

The meter traps fixed volumes of liquid and counts them. It handles viscous fluids well, even at low flow, and is a common choice for crude and fuel transfer. It has moving parts, causes pressure drop and needs a strainer upstream.

Thermal

A heated element loses heat to the passing gas, and that heat loss gives mass flow directly. It suits low-pressure gas such as flare, fuel gas, air and biogas, with good turndown. It depends on gas composition and can be affected by moisture or deposits.

Magnetic

A conductive liquid moving through a magnetic field produces a voltage proportional to velocity. There are no moving parts or obstruction, so it suits water, wastewater, slurries and chemicals. It does not work on non-conductive fluids such as hydrocarbons or on gas.

Ultrasonic

Transit-time sensors measure the difference in sound travel time with and against the flow. There are no moving parts and almost no pressure drop, and spool-piece meters can be accurate on liquids and gas. They are sensitive to entrained gas or solids and need a stable flow profile. Ultrasonic gas flow meters are available for custody transfer.

Clamp-on ultrasonic

Sensors strap to the outside of the pipe, so you can measure without cutting the line or stopping the process. It is useful for checks, temporary surveys and hard-to-shut-down lines. Accuracy is lower than an inline meter and depends on pipe condition and wall data.

Coriolis

Vibrating tubes twist in proportion to the mass moving through them, and the meter also gives density. It is very accurate on liquids and gas, regardless of viscosity. It costs more, and larger sizes are heavy and cause some pressure drop.

Vortex

Counts the vortices shed behind a bluff body in the flow. Their frequency rises with velocity, and there are few moving parts. It suits steam, gas and clean liquids, and it needs enough flow for a stable signal.

Doppler

Measures the frequency shift of sound reflected by particles or bubbles in the fluid. It suits dirty, aerated or slurry liquids, and it does not work on clean fluids with nothing to reflect the signal.

Open channel and partially filled pipe

For lines that do not run full, such as drains, channels and gravity lines. The meter combines a level reading with a velocity measurement to calculate flow.

  • Crude oil, fuel and product transfer, including LACT units
  • Well testing and production allocation
  • Chemical injection and dosing control
  • Water, steam and gas in utilities and treatment plants
  • Gas flow metering for custody transfer
  • Oil and gas, petrochemical, pharmaceutical, pulp and paper and metallurgy plants
  • Fluid, including viscosity, density and any solids or gas content
  • Line size, pipe material and available straight run
  • Operating and design pressure and temperature
  • Minimum, normal and maximum flow
  • Accuracy needed (custody transfer, allocation or control), output signal and hazardous area class

We help you choose the technology for your fluid and accuracy, supply the meter with its transmitter, and build it into skids such as LACT and chemical injection units. We also commission it and supply spares.

BrandsFleximYokogawaMagnetrolRMGPhase Dynamics
02

Level measurement

Level instruments show how much liquid or solid is in a tank, vessel, sump or channel. They can give continuous readings or a point alarm. Good level measurement protects against overflow and dry running, and supports inventory and control.

Request a quote
Level instrument with probe

Buoyancy

A displacer or float changes apparent weight as the level changes, and the instrument converts it into a signal. It works well for liquid level and for interface between two liquids. It needs a chamber or cage and regular checks for buildup.

Differential pressure

The pressure at the bottom of the vessel, compared to the top, gives level for a known fluid density. It is simple and common in pressurized vessels. Density changes cause errors, and impulse lines or remote seals need care.

Capacitive

A probe forms a capacitor with the vessel wall, and the fluid changes the capacitance. It works for point and continuous level in liquids and some solids. Coating on the probe and changes in fluid properties can affect readings.

Ultrasonic

A sensor on top sends a sound pulse and times the echo from the surface. It is non-contact and low cost for open tanks, sumps and channels. Foam, vapor, turbulence and obstructions can disturb the echo, and it suits low pressure only. Both contact and non-contact devices are available.

Magnetostrictive

A float with a magnet moves along a rod, and a pulse locates it very precisely. It gives accurate level, and often temperature, in storage and process tanks. It needs a clean fluid and a float suited to its density.

Radar

A radar signal reflects off the surface and the transit time gives level. It is non-contact and not affected by temperature, pressure or vapor, so it fits tough service. Guided-wave types suit interface and low-dielectric fluids. Cost is higher than ultrasonic.

Nuclear

A radioactive source and a detector measure level through the vessel wall, with nothing inside. It is used where other methods fail, such as extreme pressure, temperature or heavy buildup. It requires licensing, handling rules and trained personnel.

  • Separators, scrubbers and storage tanks
  • Interface level between oil and water
  • Hopper and silo inventory for solids
  • Pump protection and high or low level alarms
  • Fluid, density and dielectric constant if known
  • Vessel type, dimensions and connection size and rating
  • Operating and design pressure and temperature
  • Measuring range, and whether you need continuous level or a switch
  • Foam, vapor, buildup, agitation or an interface layer; output signal and hazardous area class

We select the technology for your vessel and fluid, supply the instrument with its transmitter or switch, and integrate it into separators, tanks and skids. We also commission it and supply spares.

BrandsMagnetrolYokogawa
FAQ

Common questions

How do I choose between Coriolis, turbine and positive displacement for crude oil?

It depends on viscosity, cleanliness and accuracy. Coriolis gives mass flow and density with little maintenance but costs more. Positive displacement handles viscous crude well. Turbine suits lighter, clean liquids. Send us the fluid data and we will recommend one.

Can you measure flow without shutting down the line?

Yes, with clamp-on ultrasonic. It is good for checks and surveys. For permanent, high-accuracy duty we usually recommend an inline meter.

Why does the fluid matter so much for level measurement?

Density, foam, vapor and buildup change how each technology reads. A radar that works well in a clean tank may struggle with foam, and a differential pressure transmitter drifts if density changes.

Do you supply instruments already built into a skid?

Yes. We integrate flow and level instruments into LACT units, test separators and chemical injection skids, and commission them as one system.

Looking for a complete system?

See how we integrate these products into skids, built and tested in our workshops.

Get a quoteSkids