Filtration skids
Filter and coalescer packages that protect your process equipment, built on ASME vessels and supported by Parker, a manufacturer we represent.

Clean fluid in, protected equipment downstream.
- Filters and coalescers for gas, liquids and lube oil
- Pressure vessels to ASME VIII Div. 1, fabricated in our workshops
- Single, duplex or multi-stage arrangements
- Differential pressure monitoring and bypass
Engineered around your fluid, tested before it ships.
This is a new addition to our range. We engineer it around your fluid and flow, fabricate the vessels in our workshops to ASME VIII Div. 1, and test the complete skid before it ships.
- Engineered to order: fluid, flow and filtration level define the skid
- Vessels fabricated in our workshops, with Parker filtration components
- Factory acceptance test (FAT) in our workshops, site acceptance test (SAT) at your site
Pressure vessels we fabricate for filtration service
Vessels and components we have supplied, photographed in our workshops and at site. A filtration skid is engineered to order around your fluid.


How it works, configurations and standards
Open the sections you need. Everything stays on the page for reference and print.
01How it works
Process diagram and step-by-step timeline
Filtration skids remove solids and liquids from gas, crude, amine, glycol, lube oil, fuel or water before they reach sensitive equipment. Vessels, filter elements, valves and instruments come together on one skid.
We design the skid around your fluid and flow, fabricate the vessels in our workshops to ASME VIII Div. 1, and build with filtration components from Parker, a manufacturer we represent.
In the order the fluid passes through it. Select a step, use the arrows, or let it play.
Typical schematic configuration, shown for reference only. The final design, equipment, instrumentation and applicable codes depend on the client's process conditions, specification and project requirements, and are defined during engineering.
Swipe sideways to see the whole diagram.
Inlet and isolation
The fluid to be cleaned enters through an isolation valve. Its flow, pressure and contaminants set the size and the filtration level.
Duplex filter vessels
Filter elements remove solids and larger droplets. With two vessels in parallel, one can stay in service while the other is isolated for an element change.
Differential pressure
A differential pressure transmitter reads the pressure drop across the filters. A rising value shows the elements are loading and should be changed.
Bypass
A bypass line with a valve lets the flow continue around the filter stage when it has to be isolated. The fluid in the bypass is not filtered, so its use depends on the process; for critical equipment the duplex arrangement is normally preferred.
Coalescer stage
A coalescer merges fine droplets or aerosols into larger ones that drain out of the stream, and stops fine particles, to protect equipment downstream.
Clean outlet
The clean fluid leaves through an outlet valve to the equipment it protects, such as compressors, turbines, instruments, pumps or bearings.
Drains
Liquid and solids collected in the vessels and the coalescer sump go to a closed drain or collection point, by manual or automatic drain.
Instruments and signals
Differential pressure and other signals go to a local panel for indication and alarms, and can go to your DCS or PLC.
02Typical configurations and options
What goes on the skid and what can change
- FluidGas, liquid or lube oil, as the application requires
- ArrangementSingle, duplex or multi-stage
- StagesFilter stage, with coalescer stage as the fluid requires
- VesselsASME VIII Div. 1 pressure vessels, fabricated in our workshops
- Filter elementsParker filtration components, selected for the fluid and the filtration level
- MaterialsCarbon steel, stainless steel, or NACE materials for sour service
- MonitoringDifferential pressure transmitter and gauges
- BypassBypass line with valve, as the process requires
- DrainsManual or automatic drains to a closed drain
- SafetyPressure relief valve sized to the vessel, where required
- InstrumentationLocal indication, with signals to a panel, DCS or PLC
- Area classificationInstruments and wiring selected for the classified area
03Standards and documentation
Design references and the documents we deliver
Designed to ASTM, ASME, ISO and API standards. The applicable codes are agreed per project.
Typical references
- ASME VIII-1Pressure vessels (filter and coalescer housings)
- ASME B31.3Process piping
- API 520 / 521Relief devices, and pressure-relieving and depressuring systems
- NACE MR0175 / ISO 15156Materials for H2S-containing (sour) service
- ASME B16.5Pipe flanges and flanged fittings
- ASME IXWelding and brazing qualifications
- ISO 4406Coding of fluid cleanliness, where a cleanliness level is specified
Typical documentation package
- P&ID
- General arrangement
- Vessel and instrument datasheets
- Design calculations
- FAT procedure and report
- Operation and maintenance manual
Factory acceptance test (FAT) in our workshops and site acceptance test (SAT) at the installation site.
Typical brands on this skid
Brands we represent, integrated alongside your preference.




