Controval
Product group

Fluid handling and filtration

Clean fluid, the right dose and tight connections keep equipment running. We supply these products on their own or build them into our skids.

At a glance

We build filtration vessels and supply dosing pumps, fittings and tubing, alone or integrated into a skid.

  • Filtration vessels built in our workshops to ASME VIII Div. 1
  • Dosing and metering pumps from Exact, Milton Roy and Pulsafeeder
  • Fittings, tubing and valves from Swagelok and Crawford
  • All three integrated into filtration, chemical injection and water treatment skids
01

Filtration

Filtration removes solids and liquids that damage pumps, compressors, instruments and process units. The right filter protects equipment and keeps the process stable. A wrong one clogs often or lets contaminants through.

Request a quote
Demineralized water filtration vessel

Amine and glycol

Cartridge filters remove particles and degradation products, and carbon beds remove dissolved hydrocarbons and other contaminants. Cleaner solvent means less foaming, fouling and corrosion. Fine filters load faster when upstream control is poor.

Lube oil and fuel

Elements keep fine particles out of bearings, seals and burner nozzles. Duplex vessels let one filter stay in service while the other is changed. Selection depends on the micron rating, viscosity, temperature and allowed pressure drop.

Water pretreatment

Bag, cartridge or media filters take out suspended solids ahead of membranes, boilers or injection pumps. The micron rating must match the downstream equipment. Water with high solids may need a coarser stage first. We also supply pretreatment ahead of ion exchange and reverse osmosis.

Backwash or disposable

Backwashable filters clean themselves with reverse flow, which suits heavy solids loads but needs a waste stream and controls. Disposable elements are simpler and cheaper to start, but need changes and disposal.

Coalescing

A coalescer merges fine droplets or aerosols into larger drops that drain from the stream, for example water out of fuel or oil out of gas. It needs a clean upstream stage and a drain, and it has a pressure drop. We supply liquid/gas and liquid/liquid coalescing systems.

Hydro-treatment

Hydro-treatment filtration systems, engineered to your fluid, flow and required cleanliness.

Drinking water

Process systems for drinking water treatment, sized to your flow and water analysis.

  • Amine and glycol loops in gas treatment and dehydration
  • Lube oil and seal oil for compressors and turbines
  • Fuel gas and liquid fuel to burners, engines and turbines
  • Water pretreatment before membranes, boilers or injection
  • Fluid, flow rate, operating pressure and temperature
  • Contaminant type and size, and the target cleanliness
  • Allowed pressure drop and how often elements can be changed
  • Materials needed, including NACE for sour service
  • Single, duplex or multi-stage, and any bypass or drain requirements

We fabricate the vessels in our workshops to ASME VIII Div. 1 and select elements for your fluid and filtration level. We can supply the filter alone, or build it into a skid with valves, instruments and a panel. Approved shop for fabrication of ASME I Stamp vessels under Section VIII Div. 1.

02

Dosing and metering pumps

A dosing pump delivers a set amount of chemical against line pressure, repeatedly and with accuracy. They are used wherever the process needs the right dose, such as corrosion inhibitor, methanol, biocide or chlorine.

Request a quote
Dosing pump skid with two metering pumps and a tank

Diaphragm

A flexible diaphragm separates the chemical from the drive, so there is no leakage past a seal. Good for hazardous or corrosive chemicals. Diaphragm life and pressure limits depend on the design and the fluid.

Plunger

A plunger moves directly in the fluid, which allows high discharge pressure and good accuracy. Suits clean fluids at higher pressure. It needs packing that wears and can leak, so it is less suited to very hazardous chemicals.

Solenoid-driven

A solenoid pulse moves the diaphragm, giving a compact, low-cost pump for small flows. Common in water treatment. It has limits on pressure and flow, and the pulsed flow may call for a damper.

Accessories

The pump alone is not the whole system. Pulsation dampeners, relief and back-pressure valves, check valves, strainers and calibration columns keep the dose accurate and the pump protected.

  • Corrosion inhibitor and scale inhibitor injection
  • Methanol and demulsifier injection
  • Chlorine, biocide and pH control in water treatment
  • Odorant and other additive dosing
  • Chemical, concentration, viscosity and temperature
  • Flow range, from minimum to maximum dose
  • Discharge pressure, and suction conditions
  • Materials compatible with the chemical
  • Control: manual, automatic by process signal, or by PLC; hazardous area class

We select the pump, drive and accessories for your chemical, flow and pressure. We represent Exact Dispensing (Exact pumps: piston and gear metering) and also work with Milton Roy and Pulsafeeder metering pumps. We can supply the pump on its own, or integrate it into a chemical injection skid with tank, controls and instruments.

BrandsExact DispensingMilton RoyPulsafeeder
03

Fittings and tubing

Instrument and process lines depend on leak-tight connections. The right fitting, tubing and valve combination reduces leaks, rework and downtime, and makes later maintenance easier.

Request a quote
Stainless steel tube fittings and tubing

Compression tube fittings

Ferrules grip the tube as the nut is tightened, giving a metal-to-metal seal that handles pressure and vibration. Tube size, wall thickness and material must match the fitting. Do not mix parts from different manufacturers.

Instrument tubing

Seamless tubing, commonly 316 stainless steel, in sizes set by the pressure rating and the line. Surface finish and hardness matter for a good seal. Special alloys are used for corrosive or sour service.

Valves and manifolds

Needle, ball and check valves and two, three and five valve manifolds isolate, vent and calibrate instruments. Using a manifold in place of separate valves reduces connections and potential leak points.

Pipe thread and adapters

NPT and other pipe threads connect tubing to equipment. Thread sealant is needed, and thread type must match: NPT, BSP and others do not interchange. Welded or flanged adapters are used at higher pressures.

  • Instrument impulse lines to transmitters and gauges
  • Sample lines and analyzer systems
  • Chemical injection and small process lines
  • Hydraulic and pneumatic lines on skids and panels
  • Tube outside diameter, wall thickness and material
  • Working pressure and temperature
  • Fluid and any corrosive or sour service
  • Thread type and size at the equipment connection
  • Existing fitting make, to avoid mixing brands

We help match fittings, tubing and valves to your pressure, temperature and fluid, and supply Swagelok and Crawford products for new builds, replacements and spares. We also use them in our skids and panels.

BrandsSwagelokCrawford
FAQ

Common questions

How do I know when to change a filter element?

Watch the differential pressure across the filter. A steady rise to the limit set for the filter shows the element is loaded. Many skids add a differential pressure transmitter and an alarm for this.

Should I choose a diaphragm or a plunger dosing pump?

Diaphragm pumps suit hazardous, corrosive or leak-sensitive chemicals. Plunger pumps suit clean fluids at higher pressure. Chemical, pressure and flow range decide it.

Why does a dosing pump need a back-pressure valve and a damper?

A back-pressure valve keeps the discharge steady so the pump does not over-dose when injecting into low pressure. A damper smooths the flow pulses, so piping and measurement are calmer.

Can I mix fittings from different manufacturers?

We advise against it. Ferrule shapes and tolerances differ between manufacturers, and mixing parts can leak or fail under pressure. Keep each connection to one maker's parts.

Looking for a complete system?

See how we integrate these products into skids, built and tested in our workshops.

Get a quoteSkids