Lube oil skids
Lube oil conditioning for turbines, compressors and engines: humidity, viscosity, pressure and temperature.

Clean oil at the right temperature and pressure.
- Controls humidity, viscosity, pressure and temperature
- For turbines, compressors and engines
- Detailed engineering and factory acceptance tests
- Remote support
What the skid looks like
Illustrative rendering of the configuration; real photos of our builds are on the projects page.

- Lubricity skid, Doha, QatarQatari Energy & Industrial Services
How it works, configurations and standards
Open the sections you need. Everything stays on the page for reference and print.
01How it works
Process diagram and step-by-step timeline
Turbines, compressors and engines depend on lube oil in good condition. Our lube oil skids control its humidity, viscosity, pressure and temperature.
We have also delivered a lubricity skid for Qatari Energy & Industrial Services in Doha, with detailed engineering, factory acceptance testing and remote support.
Lubricity skid project. Client: Qatari Energy & Industrial Services. Consignee: QatarEnergy. Detailed engineering, materials logistics and procurement, frame manufacture, instrument and equipment arrangement, FAT, crating and delivery. Deliverables: mechanical, civil, electrical and instrumentation drawings and documents, detailed engineering, FAT protocol and Data Book. Managed with remote communication and a dynamic project update methodology with the client.
In the order the fluid passes through it. Select a step, use the arrows, or let it play.
Typical schematic configuration, shown for reference only. The final design, equipment, instrumentation and applicable codes depend on the client's process conditions, specification and project requirements, and are defined during engineering.
Swipe sideways to see the whole diagram.
Reservoir and heater
Stores the oil and lets air and water settle. A heater brings cold oil to working viscosity before start-up.
Main and standby pumps
The main pump supplies the oil. The standby pump starts automatically on low pressure, so the machine is not left without oil.
Cooling and temperature
The cooler removes the heat taken from the machine. A temperature control valve holds the viscosity the bearings need.
Filtration
Duplex filters can be switched and serviced while the system runs. Differential pressure shows when a cartridge needs changing.
Pressure control
A control valve holds the header pressure steady and spills the excess back to the reservoir. A relief valve protects the system.
Machine bearings
The oil lubricates bearings and gears and carries heat away. Supply pressure and temperature are monitored at the machine.
Return
Used oil drains by gravity back to the reservoir through sloped return lines.
Moisture control
A vapor extractor, breather or offline dehydration loop removes water and vapors, protecting the bearings and the oil.
Instruments and control panel
Transmitters, switches and gauges feed a panel with pump start, alarms and trips. Signals go to the machine control system or your DCS.
02Typical configurations and options
What goes on the skid and what can change
- Oil and gradeMineral or synthetic oil; ISO VG grade as the machine builder requires
- ReservoirCarbon or stainless steel; heater, level indication, breather or vapor extractor
- PumpsMain and standby motor-driven; or shaft-driven main with auxiliary pump
- Emergency supplyOptional DC emergency pump or elevated run-down tank for critical machines
- CoolingWater-cooled shell and tube or plate; or air-cooled; with temperature control valve
- FiltrationDuplex transferable filters, or simplex with bypass; rating per machine builder
- Pressure controlPressure control valve with spill-back to the reservoir; relief valve
- Moisture controlVapor extractor, breather, or offline dehydration loop
- InstrumentationPressure, temperature, level and differential-pressure transmitters, switches and local gauges
- Control panelRelay or PLC logic for pump start, alarms and trips; signals to machine control or DCS
- Area classificationMotors, instruments and panels selected for the classified area
- Piping and cleanlinessCarbon or stainless steel piping and tubing; cleaned and flushed before shipping
- MountingSkid-mounted with drip pan; reservoir integrated or separate
- Instrument brandsWe integrate Yokogawa, Flowserve, Magnetrol, Samson and Swagelok, and consider your preference
03Standards and documentation
Design references and the documents we deliver
Designed to ASTM, ASME, ISO and API standards. The applicable codes are agreed per project.
Typical references
- API 614 / ISO 10438Lubrication, shaft-sealing and oil-control systems
- ISO 4406Coding of oil cleanliness (particle counts)
- ISO 3448ISO viscosity grades (ISO VG) for industrial oils
- ASTM D445 ยท D6304Oil viscosity; water in oil by Karl Fischer
- ASME B31.3Process piping
- ASME VIII Div. 1Pressure vessels, such as coolers and filter housings
Typical documentation package
- P&ID
- General arrangement
- Equipment and instrument datasheets
- Hydraulic and thermal calculations
- Instrument index
- FAT procedure and report
- Piping cleanliness record
- Operation and maintenance manual
Factory acceptance test (FAT) in our workshops and site acceptance test (SAT) at the installation site.
Typical brands on this skid
Brands we represent, integrated alongside your preference.




One team, from engineering to the factory test
- Step 1
Engineering
Process, mechanical and instrumentation design from your specification.
- Step 2
Fabrication
Built and assembled in our workshops to the agreed codes.
- Step 3
Factory test (FAT)
Loop-by-loop checks, valve stroking and control verification, with your witnesses if you wish.
- Step 4
Start-up
Documentation, delivery and remote support.
