Controval
Product group

Safety and protection

Relief valves and tank protection devices are the last line of defense for people, vessels and lines. We help you size them, supply them, and keep them tested and in spec.

At a glance

We select, supply, repair and test the devices that keep pressure and vacuum inside safe limits.

  • Sizing and selection of safety relief valves from your process data
  • Spare and repair recommendations for the valves you already have
  • Repair and testing of relief valves on site or in the shop
  • Tank vents, flame arresters and blanketing supplied for storage tanks
01

Safety relief valves

A safety relief valve opens at a set pressure to release fluid and protects a vessel, line or system from overpressure. It must open when needed and reseat afterward, so it needs correct sizing and regular testing.

Request a quote
Safety relief valves ready for delivery

Pilot-operated

A small pilot valve senses pressure and controls the main valve, so the main valve stays tight until close to set pressure. Good where the operating pressure is near the set pressure. The pilot can plug or foul in dirty, viscous or polymerizing fluids.

Pop and modulating

Pop valves open fully and quickly, which suits gas and vapor. Modulating valves open in proportion to the overpressure, which suits liquids and avoids slamming the full flow out at once. Pick by the fluid and the relieving case.

Spring-loaded

The simplest and most common design: a spring holds the disc on the seat until pressure overcomes it. Rugged and easy to repair. Back pressure in the discharge system changes the set point unless a balanced bellows type is used.

Low-pressure tank valves

Used on atmospheric and low-pressure tanks, where the set pressure is measured in inches of water column or ounces, not psi. Sized for tank breathing and emergency venting, usually following API 2000.

Conventional

A spring valve whose set pressure is affected by back pressure. It is simple and common where back pressure is low and steady.

Safety selector

A changeover valve connects two relief valves to one vessel, so one can be removed for test or repair while the other stays in service.

  • Pressure vessels, separators and heat exchangers
  • Pump and compressor discharge lines
  • Fire case and blocked outlet protection
  • Thermal expansion relief in liquid lines
  • Atmospheric and low-pressure storage tanks
  • Fluid, phase and relieving case (blocked outlet, fire, thermal, other)
  • Set pressure, maximum allowable working pressure and back pressure
  • Required relieving flow and operating temperature
  • Inlet and outlet sizes, connection type and materials
  • Existing valve tag, make and model, if it is a replacement or repair

We size the valve from your process data, recommend the spares to keep on hand, and repair and test valves on site or in the shop. Valves can also go on our skids, such as surge relief and chemical injection. We can also survey your installed valves in the field and recommend spare parts.

BrandsFarris
02

Pressure and vacuum valves

Storage tanks must breathe as liquid moves in and out and as temperature changes. Pressure and vacuum devices let a tank do that safely, without overpressure, collapse or loss of product vapor. We supply a complete line of vapor and flame control safety devices.

Request a quote
Pressure and vacuum relief vents on a storage tank

Relief vents

Pressure and vacuum relief vents open outward to release vapor and inward to let air or gas in. Normal venting covers pumping and temperature changes. Emergency venting covers fire exposure. Sizing usually follows API 2000.

Flame arresters

A flame arrester passes vapor but stops a flame, using a metal element with narrow passages that absorbs heat. Rated for deflagration or detonation, and for end-of-line or in-line use. Elements can foul and need regular cleaning.

Tank blanketing

A regulator adds inert gas, often nitrogen, when the tank pressure drops, keeping a small positive pressure and a low oxygen level. It cuts vapor loss and air ingress. It needs a gas supply and a relief vent for overpressure.

  • Crude, product and chemical storage tanks
  • Tanks holding flammable liquids or vapors
  • Tanks that need an inert gas cover
  • Vent lines that must stop a flame entering the tank
  • Refineries, chemical and petrochemical plants, food and beverage, terminals and pharmaceutical plants
  • Product stored, vapor group and flash point
  • Tank size, design pressure and design vacuum
  • Pumping in and out rates, and maximum temperature change
  • Whether the vent is end-of-line or in-line, and the connection size
  • Inert gas type and supply pressure, for blanketing

We help select the vent, arrester or blanketing valve for your tank and product, and supply them with the related tank equipment. We can check what you already have installed and recommend replacements or spares. We can also integrate them into your tank management solution.

BrandsProtectoseal
FAQ

Common questions

How often should a relief valve be tested?

It depends on the service, the fluid and your company or regulatory program. Clean, non-corrosive service can run longer between tests than dirty or corrosive service. Test results from the first interval usually show whether to shorten or extend the next one.

Can you size a relief valve if I only have the equipment data sheet?

Often yes, if the sheet gives design pressure, fluid and the relieving case. If the relieving case is not defined, we will tell you what is missing so the sizing is based on the real scenario.

Do I need both a relief vent and a flame arrester on a tank?

Not always. It depends on the product, the local code and your risk assessment. They are often combined when the vapors are flammable, but the decision belongs with your safety review.

Is a pilot-operated valve better than a spring-loaded one?

Neither is better in every case. Pilot-operated valves hold tighter near set pressure and handle higher back pressure. Spring-loaded valves are simpler and tolerate dirty service better.

Looking for a complete system?

See how we integrate these products into skids, built and tested in our workshops.

Get a quoteSkids